Waterstop
Product material: natural rubber and various synthetic rubbers are used as the main materials, mixed with various additives and fillers, after plastic training, mixing, and compression molding
Variety specifications: sub-bridge type, mountain type, P type, R type, U type, Z type, B type, T type, H type, E type, 0 type, etc.
Product performance: It has good elasticity, wear resistance, aging resistance and tear resistance, strong adaptability to deformation, and good waterproof performance.
Temperature application range: -45C to +60C.
(This product should not be used when the temperature exceeds +79c and when it is strongly oxidized or corroded by organic solvents such as oil.)
Scope of application: Mainly used in infrastructure projects, underground facilities, tunnels, sewage treatment plants, water conservancy, subway and other projects. It is used for pouring and pouring concrete of expansion joints such as gates, dam bottoms, construction projects and underground buildings. Thereby ensuring the service life of the engineering building
Variety specifications: sub-bridge type, mountain type, P type, R type, U type, Z type, B type, T type, H type, E type, 0 type, etc.
Product performance: It has good elasticity, wear resistance, aging resistance and tear resistance, strong adaptability to deformation, and good waterproof performance.
Temperature application range: -45C to +60C.
(This product should not be used when the temperature exceeds +79c and when it is strongly oxidized or corroded by organic solvents such as oil.)
Scope of application: Mainly used in infrastructure projects, underground facilities, tunnels, sewage treatment plants, water conservancy, subway and other projects. It is used for pouring and pouring concrete of expansion joints such as gates, dam bottoms, construction projects and underground buildings. Thereby ensuring the service life of the engineering building
Ordering Consultation
Service Hotline：
|
Product Introduction
止水帶的施工方法
橡膠止水帶是在混凝土澆注過程中部分或全部澆埋混凝土中在澆埋混凝土以前要使其在界面部位保持平展，接頭部分粘接緊固.再以適當的力充分澆搗.震蕩混凝土來定位止水帶，使其與混凝土良好的結合，一面影響止水效果。
施工注意事項
在施工過程中，由于混凝土中有許多尖角的石子和銳刃的鋼筋，所以在澆搗和定位止水帶時，應注意澆搗的沖擊力，以免由于力量過大而刺破橡膠止水帶如發現有破裂現象應及時修補，否則在接縫變形和受水壓時橡膠止水帶所能抵抗外力的能力就會大幅度降低。
固定止水帶時，只能在止水帶的允許部位上穿孔打洞，不得損壞本體部分。在定位橡膠止水帶時，一定要使其在界面部位保持平展，更不能讓止水帶翻滾、扭結，如發現有扭結不展現象應及時進行調正
在澆鑄固定止水帶時，應防止止水帶偏移，以免單側縮短，影響止水效果如圖B、C)
在混凝土澆搗時還必須充分震蕩，以免止水帶和混凝士結合不良而影響止水效果。
止水帶接頭必須粘接良好，可參考圖示(如圖A)，如施工現場條件具備，可采用熱硫化連接的方法。不加任何處理的所謂“搭接”是絕對不允許的。
止水帶貯運注意事項
止水帶在運輸與貯存時，應注意勿使包裝損壞，放置于通風、干燥處、并應避免陽光直射，禁止與酸、堿、油類及有機溶劑等接觸，且隔離熱源;應保存于室內，并不得重壓。自生產日期起半年內產品性能應符合國家標準的規定。